Products 313-324 of 382
Show
Mazworx S14/S15 IACV Spacer
Price: $42.50
Availability: In Stock
Mazworx Item #: 10173.7 -

Mazworx S14/S15 IACV Spacer is for spacing out the IACV from the plenum. It sandwiches between the plenum and IACV. It re-routes the idle vacuum line externally. So the hard line can be removed for extra fuel rail clearance. Includes O-rings, installation bolts and hose barb fitting.

Mazworx S14/S15 SR20DET Intake Manifold Spacer
Price: $34.99
Availability: In Stock
Mazworx Item #: 12000 -

This spacer is 1/2" thick and spaces your upper intake away from the lower intake so you can run a top feed fuel rail on the stock manifold. It also comes with O-rings on both sides so there's no need for a gaskets. Additional hardware bolts to accommodate this spacer can be purchased separately. Please click "Bolts" if you require them.

Mazworx SR20 Timing Chain Tensioner SR20, SR20DET, SR20VE, SR20VVL, 20V, P11, P12, S13, S14, S15, B13, B14, Pulsar, GTiR, FWD, RWD, 240SX, 200SX, 180SX, Silvia, NeoVVL
Price: $99.00
Availability: In Stock
Mazworx Item #: 10181 -

Our new SR timing chain tensioner significantly improves upon the factory hydraulic timing chain tensioner which can fail when stiffer valve springs are installed. With the stock tensioner, the installation of bigger cams and stiffer valve springs can also cause excessive timing chain wear and can cause the chain to stretch prematurely. The Mazworx tensioner does not need oil pressure to operate and, when properly adjusted, can function as well or better than a factory OEM tensioner, can...

Mazworx SR20 Torque Plate
Price: $495.00
Availability: In Stock
Mazworx Item #: 10170 -

Torque plates preload the block to simulate a cylinder head installed. This allows the cylinder to be honed for better ring seal. A must have when you have sleeves installed. Includes provisions for standard headstuds or 1/2" headstuds and up to 90mm bore.

Mazworx VVL/RWD Conversion Kit
Retail: $2,447.00
Price: $2,324.99
Availability: Built to Order 1-2
Mazworx Item #: 10185 -

This is a complete kit needed to bolt a NEO VVL SR16/20VE head onto your RWD SR20DET. Buy everything together and save time and money later. * Additional part maybe needed is the 20V cam angle sensor if you are running a stock ecu. If you are planning to run a aftermarket ecu like AEM, Haltech etc, you can run our hall sensor kit and completely eliminate the cam angle sensor.* * Pictured is with a complete intake manifold. We also have available partial intake manifolds if you want to build...

Mazworx VE/RWD Conversion Oil Pickup
Price: $130.00
Availability: In Stock
Mazworx Item #: 15050-VERWD -

This is required when doing a VVL/VE cylinder head conversion. Utilizes a S14 blacktop pickup and a VE oil pickup. The larger inlet tube on the VVL is required for the bigger VVL oil pump.

Mazworx SR FWD Distributor Block-Off
Price: $40.00
Availability: In Stock
Mazworx Item #: 10305 -

Blocks off the distributor hole on a FWD head.

Mazworx VVL Solenoid Relocation Blocks
Price: $159.99
(1)
Availability: Discontinued
Mazworx Item #: 1018 -

These are CNC machined from T-6061 billet aluminum. Required to be used when converting to a VVL head on your RWD SR20. These will move the VVL solenoids away since they will hit the firewall. Complete fittings and lines kit also available. Please check the options if you require the fittings and lines. Black lines and fittings also available.

Mazworx Water Neck/Heater Hose
Price: $95.00
Availability: In Stock
Mazworx Item #: 11184 -

Water neck with heater hose for use when using a VVL head on a RWD block. Replaces the FWD neck on the head. Allows you to retain the RWD coolant temp sensors and coolant routing.

Mazworx Billet Water Neck Inlet
Price: $50.00
Availability: In Stock
Mazworx Item #: 10400.10 -

CNC machined billet water neck inlet for the SR20. Replaces your factory water neck with this T-6061 billet unit. Installs directly to the block. Requires removal of the OEM thermostat housing. Increased water flow and better fitment. Neck is machined for -16an fittings. Oring included

Mazworx Billet Water Neck Outlet
Price: $85.00
(1)
Availability: In Stock
Mazworx Item #: 10400.20 -

CNC machined billet water neck outlet for the SR20. Replaces your factory water neck with this T-6061 billet unit. Increased water flow and better fitment. Includes: - 1/8" NPT on top - 1/4" NPT on front Neck is machined for -16an

Line Lock Kit, S13/S14
Price: $275.00
Availability: In Stock
Mazworx Item #: 81200 -

Line lock kit for S13/S14. The installation of this kit will assist you during burnout and staging processes. Includes necessary hardware to fit the S13/S14.