Products 145-156 of 466
Show
Availability: In Stock
Mazworx
Item #: 30105.10 -
Billet SR20 oil pan specifically designed for FWD applications using the FWD block (will not work on AWD blocks). Center sump with baffle to trap oil during acceleration and braking. Oil fitting set on the exhaust side.
Availability: Built to Order 1
Mazworx
Item #: 7030 -
This intake kits fits our G25-550/660 and G30-660/770/900 turbo kits.
Availability: Built to Order 1-2
Spec Clutch
Item #: SPEC-ST63PT-MZX -
This is Spec's Super Twin that was made to fit our JZVQ Bell Housing.
Availability: In Stock
Mazworx
Item #: 10164.1 -
Allows you to attach an air filter to the VH45 MAF. Tube size is 3-1/2"
Availability: In Stock
Mazworx
Item #: 10145.5 -
Reverse Lock Out plate for Z33 and Z34 transmissions. Made from 3/16" laser cut stainless steel. Slotted for adjusting.
Availability: In Stock
Mazworx
Item #: 13264-P1 -
This valve cover is a hybrid between the P11/P12 and S14. It's designed for RWD applications when using a VE head. CNC machined from billet 6061-T6. Full internal S14 style baffling with 3x -10an breather fittings. Custom low profile oil fill cap. Designed to fit R35 ignition coils without any extra brackets. Uses orings instead of OEM gaskets. We provide half moons to fill in the head so the orings will seal. You will cut down the rear...
Availability: Back Order
Mazworx
Item #: 60150.10 -
Now we offer just the bell housing. This kit comes complete with all you need to upgrade the transmission in your FRS/BRZ/GT86. It is known that making over 400hp on the stock trans is certain death. Now we have the solution. The only part you will need to source is a replacement clutch disc with a Nissan spline. You will still use your pressure plate/flywheel, starter, and release bearing assembly. If you are running a twin disc, we recommend going to to the Tilton hydraulic release bearing...
Availability: Back Order
Mazworx
Item #: 60150.NT -
Now we offer the kit without the new transmission. This kit comes complete with all you need to upgrade the transmission in your FRS/BRZ/GT86. It is known that making over 400hp on the stock trans is certain death. Now we have the solution. The only part you will need to source is a replacement clutch disc with a Nissan spline. You will still use your pressure plate/flywheel, starter, and release bearing assembly. If you are running a twin disc, we recommend going to to the Tilton hydraulic...
Availability: In Stock
Darton
Item #: 300-035-SF -
This is for an individual sleeve. It has a single flat and will be used for cylinder 1 and 4.
Availability: In Stock
Darton
Item #: 300-035-DF -
This is for an individual sleeve. It has double flats and will be used for cylinder 2 and 3.
Availability: Back Order
Mazworx
Item #: 11196.6 -
These 60mm Individual Throttle Bodies fit the SR20VE P11 head. ITBs are at an angle to straighten flow into the runner. Manifold port is larger than stock and is designed to fit our Stage 3NA CNC port. They measure 6" from venturi to intake flange. Comes completely assembled with all 4 ITBs, billet runners, TPS, fuel rail, and throttle linkage with cable. Does not come with injectors. Runners have bosses pre-drilled on bottom to accommodate either nitrous nozzles or for vacuum ports. ...
Availability: In Stock
Mazworx
Item #: 10150.6 -
Z32 shifter bushing for the lower linkage.Bolt sold as an option.