Products 361-372 of 448
Show
Mazworx SR Dry Sump Kit
Price: $3,625.00
Availability: Built to Order 1-2
Mazworx Item #: 30100 -

The use of a wet or dry sump oiling system is often determined by the level of competition and the racers budget. A wet sump system is based on the OE oiling system and can be enhanced by certain components to improve oil control and increase power. A dry sump system is designed for the top levels of racing where maximum power and oil control are absolutely essential. Here are several advantages of dry sump over oil sump setups: - Because a dry sump does not need to have an oil pan big enough...

SR20 ACL Race Bearing Kit
Price: $116.18
Availability: In Stock
ACL Item #: 1T2964 -

They are an H-Series (harder material and more clearance) race bearing. These will fit in standard SR rods and mains.ACL Thrust Bearings for any SR motor. These can be used in standard rebuilds or all out race motors.HX Bearing give 0.001" extra clearance.19mm Rod Bearings require machining of rods.Single hole Main Bearings not available.

Mazworx Chrome Moly Steel U-Weld Roll Bar Kit, NHRA Spec
Price: $385.00
Availability: Built to Order 1-2
Mazworx Item #: Uweldrbcm -

Mazworx Chrome Moly Steel U-Weld Roll Bar Kits are made from 1-3/4" x 0.083" Chrome Moly Steel Tubing. This is upgraded material and will meet NHRA regulations. Each roll bar is made for each specific chassis. Please check your sanctioning body for exact requirements. Basic roll bar is a 4 point which includes: Base Plates Hoop with Harness Bar and Diagonal (if purchased) welded together Rear Bars Rear Strut Tower Bar (if applicable to chassis) 6 Point Option includes both side door bars and...

Mazworx Mild Steel U-Weld Roll Bar Kit
Price: $325.00
Availability: Built to Order 1-2
Mazworx Item #: Uweld -

Mazworx Mild Steel U-Weld Roll Bar Kits are made from 1-3/4" x 0.120" DOM Mild Steel Tubing. This is standard material and will meet SCCA and NHRA regulations. Each roll bar is made for each specific chassis. Please check your sanctioning body for exact requirements. Basic roll bar is a 4 point which includes: Base Plates Hoop with Harness Bar and Diagonal (if purchased) welded together Rear Bars Rear Strut Tower Bar (if applicable to chassis) 6 Point Option includes both side door bars and...

Mazworx Power Steering Adapter Kit, VH to S-Chassis
Price: $155.00
Availability: In Stock
Mazworx Item #: 10165 -

The kit includes everything you need. High Pressure Line with adapter fittings, Low pressure line, feed line, fire sleeve and misc hardware.

KA24E Exhaust Flange
Price: $45.00
Availability: In Stock
Mazworx Item #: 965507 -

Specifications: - Made from 1/2" thick 1018 cold rolled steel - CNC machined - Stepped to accept 1 1/2" sch. 10 pipe Made in the USA.

Mazworx VH45DE Headers, S13/S14 (set) S13, S14, S15, RWD, 240SX, 200SX, 180SX, Silvia, Kouki, Zenki
Price: $599.00
Availability: In Stock
Mazworx Item #: 10162 -

These headers are for the VH45DE swap into an S13/S14 chassis. The stock manifolds on the VH do not clear the frame rails or steering column. So using these headers clears them and also gives you more power with the header construction. Some clearaning required and designed to fit our motor/trans mounts. WILL NOT FIT OTHERS SWAP MOUNTS.Shown with optional coating.

Seadoo Rotax 1/2" Head Stud Kit
Price: $180.00
Availability: Built to Order 1-2
Mazworx Item #: R12HSK -

More boost means you need more clamping force on the head gasket. This upgrades the current 11mm studs to 1/2" (12.7mm). Allows more torque on the stud without excessive stretching. Requires machining to block and head (see machining section).

4-Tec Sleeved Block Sea-Doo, 4-Tec, Bombardier, Darton sleeves Rotax, Rotax
Retail: $1,570.99
Price: $1,510.99
Availability: Built to Order 1-2
Mazworx

Here at Mazworx, we can prep your block to your specifications. Utilizing our CNC capabilities and state-of-the-art equipment, you can ensure that the machining process is done properly. For more understanding of our process, see the additional information section. You must send your block in as we done with stock cores. Each prepped block will start with the following:- Hot tank cleaning- Darton Sleeves Installed- Bore & Hone w/ Torque Plate- Step Decked ...

Mazworx SR20 Cam Timing Tool SR20, SR20DET, SR20VE, SR20VVL, 20V, P11, P12, S13, S14, S15, B13, B14, Pulsar, GTiR, FWD, RWD, 240SX, 200SX, 180SX, Silvia, NeoVVL, Kouki, Zenki, Sunny
Price: $15.00
Availability: In Stock
Mazworx Item #: 10000 -

Cut from 1/8" aluminum, this tool is great in help setting your cam timing. Just align the marks on the tool with the cam gear and install the chain. Perfect tool when installing new cams or head gasket.

SR20 Sleeved Block Mazworx, nissan, sr20, sr20det, sr20ve, darton sleeves, darton sleeves sr20
Retail: $1,890.99
Price: $1,808.99
Availability: Built to Order 1-2
Mazworx Item #: 30300 -

Here at Mazworx, we can prep your block to your specifications. Utilizing our CNC capabilities and state-of-the-art equipment, you can ensure that the machining process is done properly.  This is a ready-to-assemble sleeved block that has all the necessary machine work done and all the clearances checked. Each sleeved block will start with the following: - Hot tank cleaning- Sand Blasted Block- R/R Oil Port Plugs- R/R Block Small Parts- Oil Grooved Machined- Darton Sleeves Installed- Bore...

Darton SR20 Dry Sleeves
Price: $420.00
Availability: In Stock
Darton Item #: 300-035-SF/DF -

The Darton SR20DET Dry Sleeve Kit is made from Darton's famous high strength Ductile Iron and designed specifically for the Nissan SR20DET blocks. The new sleeves will be supplied for bore sizes from 86mm - 90mm. The new multi-diameter sleeve, with flats assures max-wall thickness for strength at any bore size.